MESO-Rx Sponsor Genuine Steroid Powder Manufacturer-AASraw

[cousinmuscles]

(Sorry English is not my native language)
Has anyone brewed new test cyp from AAsraw?
I have a lot of experience in brewing
It smells like cyp but it doesn't dissolve.

250mg/ml
25%BB (I live in a cold country)
1%BA
MCT
a lot heat

it reminds me of sticky bold U from QSC
View attachment 368489
View attachment 368488

Wrong thread, as if it is the vendors fault.
In this case I would place that beaker on a hotplate, set at 100c, and let it sit for a very long time, until you see it dissolving, and carefully mix to get all the liquid to eventually reach the melting point. Might take well over a day, dunno tbh never tried such a large amount.

I did my first brew 7 years ago too. First thing I learned is melt the raws completely first alone in the beaker, then add solvents, then add carrier oil.

How do you filter all of this and how do you insert it into vials?

 

[The-Squat]

Wrong thread, as if it is the vendors fault.
In this case I would place that beaker on a hotplate, set at 100c, and let it sit for a very long time, until you see it dissolving, and carefully mix to get all the liquid to eventually reach the melting point. Might take well over a day, dunno tbh never tried such a large amount.

I did my first brew 7 years ago too. First thing I learned is melt the raws completely first alone in the beaker, then add solvents, then add carrier oil.

How do you filter all of this and how do you insert it into vials?

Yeah, wrong thread, as this does no justice to the vendor and puts it on high alert.

If @pipo didn't ask that question I am willing to bet people would have panicked on these raws and started talking crap to the vendor because of current test results on the tren e.

I had done this same thing over 15 years ago, smaller amount, it took a very long time and non stop stirring. I knew better but had my head up my ass that day.

 

[Photon]

because of current test results on the tren e.

it almost seems like nobody bought it (aside from me and one other guy)

 

[pipo]

Anyway, back to holding sources accountable and doing the right thing.

@AASraw Boss, come here and make an official statement on Tren E raws. Don't hide. We can see when you are online.

 

[The-Squat]

Assuming he made 5000ml, that's 1350g of raws, when I did it and it took forever to melt, was either 250ml or 500ml, 65g to 135g or raws.

I'm not sure he will get this done!

 

[Grally]

I just brewed
100ml
200mg/ml
25% BB
2% BA
without adding MCT

no results
It smokes but doesn't melt

I can't tell you the temperature
I don't have a temperature sensor on my magnetic stirrer

Maybe cyp dissolved and is this ballast substance?

 

[The-Squat]

I just brewed
100ml
200mg/ml
25% BB
2% BA
without adding MCT

no results
It smokes but doesn't melt

I can't tell you the temperature
I don't have a temperature sensor on my magnetic stirrer

Looks like it's trying to melt but the heat is too high if it smokes.

Is it smoke or steam?

 

[Photon]

I just brewed
100ml
200mg/ml
25% BB
2% BA
without adding MCT

no results
It smokes but doesn't melt

I can't tell you the temperature
I don't have a temperature sensor on my magnetic stirrer

Maybe cyp dissolved and is this ballast substance?

 

[The-Squat]

View attachment 368520

I'm at a loss with this guy, I'll wait for someone else to report.

Just because it steams does not mean it won't melt, means heat is too hot and evaporation is happening before powder is fully melted. Not being a good thing for final results.

 

[The-Squat]

Do you all remember the guy that pissed Buck off with the Mast E, but turned out the guy had no clue what he was doing as everyone else had 0 issues?

Might be the same thing here!

 

[pipo]

I just brewed
100ml
200mg/ml
25% BB
2% BA
without adding MCT

no results
It smokes but doesn't melt

I can't tell you the temperature
I don't have a temperature sensor on my magnetic stirrer

Maybe cyp dissolved and is this ballast substance?

Bro make a topic on homebrew section and you will receive answers

 

[007R]

(Sorry English is not my native language)
Has anyone brewed new test cyp from AAsraw?
I have a lot of experience in brewing
It smells like cyp but it doesn't dissolve.

250mg/ml
25%BB (I live in a cold country)
1%BA
MCT
a lot heat

it reminds me of sticky bold U from QSC
View attachment 368489
View attachment 368488

I made 400ml at 250mg with 24% BB and 2% BA at 80°C and everything turned out perfectly, but there was quite a bit of impurity. It took 1 hour stirring at 80°C, then I lowered it to 60°C and added BA for another 15 minutes stirring and filtering. By the way, my cypionate powder smells like pineapple.

 

[Grally]

I just brewed
100ml
200mg/ml
25% BB
2% BA
without adding MCT

no results
It smokes but doesn't melt

I can't tell you the temperature
I don't have a temperature sensor on my magnetic stirrer

I made 400ml at 250mg with 24% BB and 2% BA at 80°C and everything turned out perfectly, but there was quite a bit of impurity. It took 1 hour stirring at 80°C, then I lowered it to 60°C and added BA for another 15 minutes stirring and filtering. By the way, my cypionate powder smells like pineapple.

I made 400ml at 250mg with 24% BB and 2% BA at 80°C and everything turned out perfectly, but there was quite a bit of impurity. It took 1 hour stirring at 80°C, then I lowered it to 60°C and added BA for another 15 minutes stirring and filtering. By the way, my cypionate powder smells like pineapple.

Did you filter this impurity or did they dissolve?
Can you take photo finished product?
Thank you for help

 

[The-Squat]

Did you filter this impurity or did they dissolve?
Can you take photo finished product?
Thank you for help

Did you turn the temperature down and let it dissolve? What you saw was the actual hormone not impurities.

You had the temperature too high causing it to vaporize while it was still trying to dissolve.

You have no idea what the hell you are doing!