MESO-Rx Sponsor Primal Pharma - US Domestic

Whats the current batch of MastP200 on sale right now?
Don't see this 25% underdosed being address anywhere.
The solution was mentioned above. Get it? Solution, haha.

Tie each batch number to a common batch/pot that is tested. Not sure how many more ways to say it.

Extra points for using a volumetric flask to get superior brew accuracy. Avoids steroid brew calculators. Exact mg/ml.

Make all your shit in some combo of 6L, 4L, 2L, 1L vol flasks. Throw it all in common 10 L beaker, mix and test. Filter and then into vials. Big batch, all 900+ vials (10 ml) have same composition. Homogeneous Solution. Done. Going Big, Big Ape style.

High quality 10 L beaker. Cheap.

Vol flasks are pricier. Pay for quality and accuracy.
 
Last edited:
Whats the current batch of MastP200 on sale right now?
Don't see this 25% underdosed being address anywhere.
Apes, I’ll circle back in this thread as I work through replies. We’ve never had this many orders in a day, so I’m head down getting everything out.

On the Mast result, that’s unusual and I’m digging in now. All Mast is labeled with the correct batch numbers. @Mastedon I’ll reimburse your testing and I have a few questions for you so we can line everything up.
It was being looked into. Idk if they have chatted or reached a conclusion to report yet. Im looking forward to it though. More mastp200 results would be awesome. I stuck to mastp100 incase it caused me pip, havent tried it yet though (or ever before)
 
It was being looked into. Idk if they have chatted or reached a conclusion to report yet. Im looking forward to it though. More mastp200 results would be awesome. I stuck to mastp100 incase it caused me pip, havent tried it yet though (or ever before)

I personally think 200 is the superior option, i'd reckon most can do 150 without pip. Or somewhere between >100-150
 
I personally think 200 is the superior option, i'd reckon most can do 150 without pip. Or somewhere between >100-150
I have so much Mast P in 100mg/ml concentration, and it annoys me. I'd love to have 50% less vials @ 150mg/ml. I also like to make my own blends, and 200mg/ml is perfect for that as I typically need high concentration gear to get ratios correct, and can really only use Mast E for them typically.


My current 1ml/day blend that I adjusted ratios on just today:
20251101_140157.webp
 
I have so much Mast P in 100mg/ml concentration, and it annoys me. I'd love to have 50% less vials @ 150mg/ml. I also like to make my own blends, and 200mg/ml is perfect for that as I typically need high concentration gear to get ratios correct, and can really only use Mast E for them typically.


My current 1ml/day blend that I adjusted ratios on just today:
View attachment 358638
Do you just keep your opened vials exposed in your container?

Maybe i’m too stickler because of my profession but I never leave any vials exposed (i’ll put a fresh alcohol swab inbetween the stopper and the cap that belongs to the vial and “seal” it that way
 
Do you just keep your opened vials exposed in your container?

Maybe i’m too stickler because of my profession but I never leave any vials exposed (i’ll put a fresh alcohol swab inbetween the stopper and the cap that belongs to the vial and “seal” it that way
Even low/average quality stoppers will stay sealed after many dozens of punctures, so my only protocol there is to wipe everything with 70% isopropyl alcohol and wait ~15 seconds for it to do it's thing, then I puncture the vial. I have vial seal aluminium stickers for anything that would be sitting long term, or is getting freezer storage. Never had an issue or infection after 20+ years and thousands of injections.
 
Do you just keep your opened vials exposed in your container?

Maybe i’m too stickler because of my profession but I never leave any vials exposed (i’ll put a fresh alcohol swab inbetween the stopper and the cap that belongs to the vial and “seal” it that way
I have a few of these that I use. If nothing else, it gives me peace of mind.
1762037959637.webp
 
Even low/average quality stoppers will stay sealed after many dozens of punctures, so my only protocol there is to wipe everything with 70% isopropyl alcohol and wait ~15 seconds for it to do it's thing, then I puncture the vial. I have vial seal aluminium stickers for anything that would be sitting long term, or is getting freezer storage. Never had an issue or infection after 20+ years and thousands of injections.
Yeah It sounds like i’m just being way too extra lol. I hope I didn’t come off as know it all or judgy! I was just curious. But if you’ve had no problems in that long of a time then i’m sure it’s safe practice
 
I personally think 200 is the superior option, i'd reckon most can do 150 without pip. Or somewhere between >100-150
Appreciate the opinion. I got enough to run a cycle and get a feel for it. Likely get the 200mg next but wanted to see how I responded and what my doses would be looking like first.

I havent really experienced any pip until a couple days ago. Still not sure what I did but test-e into the right delt turned into pip and swelling the following day. A little red next day and better today. I might have fucked up and pinned the same delt twice in a row.. but ill never know because of who I am as a person.
*and the copious amounts of cannabis that I consume regularly
 
What on earth are those that looks interesting, do they stick well to the vial? Is it sterile? What even is it
It is a 5-30ml vial cap. It fits nice and snug. Originally purchased for my bac water, but fits most large vials as well. I use an alcohol swab on it before putting it back on.

I purchased mine from a peptide accessory website, but I’ve seen them on Amazon as well.
 
Just bought a novo 4 pen for my GH injections now and have another pen for various peptides
Is pharma grade truly worth the extra ? LIke Pfizer Nglena pens or cinnatropin better than generic? some people say like 2iu of those = like 6iu generic.
 
Back
Top