SLU-PP-332 Solution Discussion

[actionjackson6699]

alright thank you, What oil would work? i tried dmso and destilated water but that didnt worked.

How are you mixing them? The way you mix matters. Supposedly some folks are using dmso + water. I currently use mig840 but any oil should work if you heat it first and keep it moving then very slowly drip the concentrated DMSO stock solution into it. That being said synthetic solvents like peg400 + PG should also work at low concentrations (like 1.5mg/ml) they would probably be the easiest to mix. Kimera chems sells an injectable that uses those solvents without DMSO. Lots of oral sarms are sold using those solvents as well, I would take those before taking 100% DMSO daily, less risk of pulling in some other toxins.

 

[actionjackson6699]

For their oral mixes seems like kimera uses DMSO + peg400. Would probably be the absolute easiest to way to get it into an oral solution at high concentration.

 

[ThreeSix]

would it also dissolve in vg/pg? 50:50?

 

[mongo5165]

I bet something like this might work as well

SuspendRx™ Anhydrous Oral Suspension Vehicle (Sweetened) | Sweetened — SpecializedRx SuspendRx™ Anhydrous Oral Suspension Vehicle (Sweetened)

 

[actionjackson6699]

Has no one else experimented with making a stable injectable solution? My longest stable formula has been. SLU at 6mg/mg + Poloxamer 188 at 5mg/ml (a surfactant that keeps the slu from recrystallizing) using 1%BA + 8%DMSO + 20%BB + 36%MiG840 + 35%EO. Makes a hazy solution due to the polox but its been room temp stable for months. It should filter fine but remain hazy due to the polox. I think there is too much polox and need to try lowering that a bit. I have also used a simpler 8%DMSO + 1%BA + 15%BB + 76%MiG840 solution and its clear and filters initially but over time when using it the slu starts crystallizing and sticking to the sides of the vial and you need to run the vial through a sonicator cycle or two to get it clear again which is annoying. Have been dosing 1-3mg of slu this way morning and night and its a smooth pin with no pip.

 

[Photon]

Has no one else experimented with making a stable injectable solution? My longest stable formula has been. SLU at 6mg/mg + Poloxamer 188 at 5mg/ml (a surfactant that keeps the slu from recrystallizing) using 1%BA + 8%DMSO + 20%BB + 36%MiG840 + 35%EO. Makes a hazy solution due to the polox but its been room temp stable for months. It should filter fine but remain hazy due to the polox. I think there is too much polox and need to try lowering that a bit. I have also used a simpler 8%DMSO + 1%BA + 15%BB + 76%MiG840 solution and its clear and filters initially but over time when using it the slu starts crystallizing and sticking to the sides of the vial and you need to run the vial through a sonicator cycle or two to get it clear again which is annoying. Have been dosing 1-3mg of slu this way morning and night and its a smooth pin with no pip.

It doesn't crystalise, it precipitates out of the solution because it can't actually hold it. Solubality data can be found on this page but it's usually too optimistic. The reality is that it's usually lower that what's listed. Personally I'd rather inject a suspension than one with dmso. The only solvent doing any work is the DMSO.

I don't use slu so I can't comment about anything else.

SLU-PP-332 | Estrogen/progestogen Receptor agonist | CAS 303760-60-3 | Selleck

SLU-PP-332 is an agonist of pan-<b>Estrogen Receptor</b>/ERR with EC50 values of 98nM, 230nM, and 430 nM for ERRα, ERRβ, and ERRγ, respectively with the highest potency for ERRα. SLUPP-332 amplifies mitochondrial function and cellular respiration in skeletal muscle cell lines and also offers...

www.selleckchem.com

 

[actionjackson6699]

It doesn't crystalise, it precipitates out of the solution because it can't actually hold it. Solubality data can be found on this page but it's usually too optimistic. The reality is that it's usually lower that what's listed. Personally I'd rather inject a suspension than one with dmso. The only solvent doing any work is the DMSO.

I don't use slu so I can't comment about anything else.

SLU-PP-332 | Estrogen/progestogen Receptor agonist | CAS 303760-60-3 | Selleck

SLU-PP-332 is an agonist of pan-<b>Estrogen Receptor</b>/ERR with EC50 values of 98nM, 230nM, and 430 nM for ERRα, ERRβ, and ERRγ, respectively with the highest potency for ERRα. SLUPP-332 amplifies mitochondrial function and cellular respiration in skeletal muscle cell lines and also offers...

www.selleckchem.com

It can hold it, it's just not stable. If it couldn't hold it, It would just crash out of solution rapidly.. also sonication would not make it clear again. The crystals are slowly forming over weeks...not immediately.

I prefer accurate dosing to randomly dosing using a suspension. By the end of the vial your probably just injecting oil. Keep your DMSO clean (which you should do with anything you're injecting) and your shouldn't have issues...it's only 8% after all ..

 

[Photon]

It can hold it, it's just not stable. If it couldn't hold it, It would just crash out of solution rapidly.. also sonication would not make it clear again. The crystals are slowly forming over weeks...not immediately.

I prefer accurate dosing to randomly dosing using a suspension. By the end of the vial your probably just injecting oil. Keep your DMSO clean (which you should do with anything you're injecting) and your shouldn't have issues...it's only 8% after all ..

Sonicate your suspension before each injection

 

[actionjackson6699]

Sonicate your suspension before each injection

Still won't be the same as using DMSO. It will not be clear. Maybe with some thick ass castor oil it will stay uniform enough to get a syringe filled. But I prefer a nice 31g insulin syringe.