If there is test-e in it that may be the culprit of pip.
MESO-Rx
Anabolic Steroids
Qingdao Sigma Chemical Co., Ltd (International, US, EU, Canada and Australia domestic
- Thread starter Qingdao Sigma Chemicals
- Start date
fooba
Member
test tren mast mixes usually use short esters so thats likely not the case
In the beginning, after all of my noob reading, I initially started drawing with 18ga and pinning with 25ga for my first cycle with pins. I had no problems for a long time, so I kept using the same consumables until I ran into stoppers that were more easily chewed up.
18ga wasn't the worst, but over time I definitely saw a few tiny rubber chunks. I searched for this problem and found that not all stoppers are equal, but some people just mitigate this by using smaller needles.
I re-filtered that vial and tried drawing with 25ga. I had no problem with that, and it's what I use for drawing now.
Could your vial be under a lot of vacuum, making it more difficult to draw? Maybe you need a temporary vent to help equalize. Some of my peptides have been under incredible vacuum, where all bac water was pulled through a 25ga needle quickly upon insertion of the needle - I didn't even have to push the plunger, the vacuum sucked it down!
Are you pulling the plunger down farther than the amount you are trying to draw, to create more vacuum?
In the grand scheme of things I'm still relatively new to this, but Test Prop in MCT flows very easily for me at room temperature. And warming the oil makes it flow very quickly, even through a 0.22μm filter.
If these are very simple solutions that you have already tried, I apologize and hope you figure it out quickly. Re-filtering gear isn't the worst, but I'm sure we would all rather be doing other things.
The test ester that Ripped Blend uses is supposed to be Test Prop.
Justaguy99
Member
March 30 - arrived this week
RaddishPork
Member
I have never had issues with coring. I don't go lower than 25G though.
When I worked in pharmacy we'd use 18g needles and you could get few jabs before the rubber gave out.
Make sure you hit the vial at a 45 degree angle and once the needle starts to penetrate, turn it straight up and continue going through until the needle is all the way in. Start at an angle, and end going straight down.
Also I'm sure YOU know this, but I'll say it for the newbies who scroll past.... Don't hit the same area of the stopper every time. If you use a smaller needle you can get like 15 draws out before they start overlapping
I’ve gone through multiple vials drawing with a 23g and have never had a problem with rubber in any of my vials.
Jurgen
Member
I draw with an 18 and frequently get some stopper in my vials. Either avoid pulling it up or filter it. Hasn’t been an issue either way. Why would you knowingly inject the rubber? I inspect everything carefully when pulling and pinning and make sure there’s nothing foreign in the syringe.
Is this the new batch of primo that’s recently been available ?
Bakes93
Member
Wondering the same thing!
DB_636
Member
It would have to be. Primo has been out of stock for a bit.
Bakes93
Member
Good point, I was thinking the same thing but I ordered my primo the day it became available & haven't received it yet, then to have sent it off to jano for testing all in a 2 week window is impressive by Mr Postman! Anyway, like OP said — looks great and if that's the latest batch I'm over the moon.
On a side note, has Anyone got janoshik results on latest batch of Test-Cyp? If they were already posted lately my apologies.
Last edited:
DB_636
Member
Latest batch was 255mg.
Bakes93
Member
Amazing, ordering that next once my primo touches down. These numbers are great. What page # on this thread was that posted on? Sorry my phone is a slow laggy piece of crap it skips all over the place, I'll hunt it down if I must.
You've been most helpful, appreciate you brother.
clearheaded
Member
go to test results thread...
Bakes93
Member
Didn't know there was one, thanks I'll check it out!
Qingdao Sigma Chemicals
Subscriber
Beautiful
Yes the new batch of primo I ordered internationally as soon as it came out
Yes new batch purchased recently
Similar threads
