RockyP
Member
Did you add any additonal solvent or just mix the oils?Damn! Just checked both of my blends and they are crystal clear. I did add a bunch of other compounds, including TNE.
Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
Did you add any additonal solvent or just mix the oils?Damn! Just checked both of my blends and they are crystal clear. I did add a bunch of other compounds, including TNE.
Any more details of the blend (compounds/volumes) you made?Damn! Just checked both of my blends and they are crystal clear. I did add a bunch of other compounds, including TNE.
no solvents. I've BB i could add, but would genuinely be just adding random volumes of solvent blindly if i do. Edit: Oops that question was for @DeodatoFulci, not me.Did you add any additonal solvent or just mix the oils?
Just took a bunch of my favorites and mixed them into a 30ml and 10ml vial. Got some ideas from posts here on meso.Did you add any additonal solvent or just mix the oils?
Mine look clear too below the line of the liquid. It's above the waterline where the crystalization shows. Seems wetting the crystals masks them, i assume due to similar refractive index of the crystals and the oil, or something like that.Damn! Just checked both of my blends and they are crystal clear. I did add a bunch of other compounds, including TNE.View attachment 378933
I threw in the kitchen sink. Haha. Got these ideas from posts here on meso.Any more details of the blend (compounds/volumes) you made?
This crystallization might clear up with a bit of heat on the side of the vial as long as the liquid can reach it. It's a whole lot better than it was as pure Anadrol,

This is helpful. I see the anadrol is down to about 10 mg / ml in each. That's quite the dilution but that may be what it takes to hold. I would hope to get it to at least 15 mg / ml so that a 2 cc pin would get at least a decent amount of anadrol in. But seems that 25 / ml is still not holding per @Whistles77 experience.
Looks like it's not far off holding though. I can play a bit if you'd like....for science. If i add 4ml more TNE, then i'll have 16ml of TNE 29.8mg/ml, Anadrol 20.2mg/ml. That'd be usable for me.This is helpful. I see the anadrol is down to about 10 mg / ml in each. That's quite the dilution but that may be what it takes to hold. I would hope to get it to at least 15 mg / ml so that a 2 cc pin would get at least a decent amount of anadrol in. But seems that 25 / ml is still not holding per @Whistles77 experience.
I think it will hold at some lower concentration. The practical issue as I see it is making sure the blend holds for a few days at room temp prior to pinning it, otherwise we'll end up with the same problems we had from the anadrol itself in terms of PIP, delayed injection site reactions, etc. if it re-crashes post-injection.Looks like it's not far off holding though. I can play a bit if you'd like....for science. If i add 4ml more TNE, then i'll have 16ml of TNE 29.8mg/ml, Anadrol 20.2mg/ml. That'd be usable for me.
Agree. I'll see how this one goes. I'm kinda optimistic this will be usable already....although there's zero chance i'll be doing any room temp pins.I think it will hold at some lower concentration. The practical issue as I see it is making sure the blend holds for a few days at room temp prior to pinning it, otherwise we'll end up with the same problems we had from the anadrol itself in terms of PIP, delayed injection site reactions, etc. if it re-crashes post-injection.
Maybe Room Temp is too high of a bar. If the blend can hold in an ambient temp of 100F or so, I'd take that as a win. But of course, def warm / heat prior to pinning no matter what.Agree. I'll see how this one goes. I'm kinda optimistic this will be usable already....although there's zero chance i'll be doing any room temp pins.
I was forced to only use 8ml of the anadrol since 2ml was severely crashed. I was able to salvage the remaining anadrol for the smaller 10ml vial blend.This is helpful. I see the anadrol is down to about 10 mg / ml in each. That's quite the dilution but that may be what it takes to hold. I would hope to get it to at least 15 mg / ml so that a 2 cc pin would get at least a decent amount of anadrol in. But seems that 25 / ml is still not holding per @Whistles77 experience.
1000%, i will always warm up these vials before administration.Maybe Room Temp is too high of a bar. If the blend can hold in an ambient temp of 100F or so, I'd take that as a win. But of course, def warm / heat prior to pinning no matter what.
Thats actually a good question, i need to test drive them this weekend. I have a bulletproof vts smith machine attachment for my rack setup that will be used for the first time this weekend, so this is a perfect cause for celebration. I’ll try the one with m-tren first. Haha.So how do you decide which to use.
I like the right one more but the left does have dbol in it.
glutathione yes (previous batch, not the one that is being sold now, but will likely grab some of that also) - great product. largely painless IM pin. i do 1cc daily.Anyone use Arail glutathione or NPP currently?
Thanks brother. Does it come reconstituted?glutathione yes (previous batch, not the one that is being sold now, but will likely grab some of that also) - great product. largely painless IM pin. i do 1cc daily.
