Arail Pharmaceuticals - US Domestic

Damn! Just checked both of my blends and they are crystal clear. I did add a bunch of other compounds, including TNE.
Any more details of the blend (compounds/volumes) you made?

This crystallization might clear up with a bit of heat on the side of the vial as long as the liquid can reach it. It's a whole lot better than it was as pure Anadrol,
 
Damn! Just checked both of my blends and they are crystal clear. I did add a bunch of other compounds, including TNE.View attachment 378933
Mine look clear too below the line of the liquid. It's above the waterline where the crystalization shows. Seems wetting the crystals masks them, i assume due to similar refractive index of the crystals and the oil, or something like that.

Edit: heated photo dissolved quite a lot. Think this will work as long as I can wet heat the sides of the vial. When vial empties it’s going to get harder.
 

Attachments

  • IMG_9443.webp
    IMG_9443.webp
    511.8 KB · Views: 14
I threw in the kitchen sink. Haha. Got these ideas from posts here on meso.

View attachment 378940
This is helpful. I see the anadrol is down to about 10 mg / ml in each. That's quite the dilution but that may be what it takes to hold. I would hope to get it to at least 15 mg / ml so that a 2 cc pin would get at least a decent amount of anadrol in. But seems that 25 / ml is still not holding per @Whistles77 experience.
 
This is helpful. I see the anadrol is down to about 10 mg / ml in each. That's quite the dilution but that may be what it takes to hold. I would hope to get it to at least 15 mg / ml so that a 2 cc pin would get at least a decent amount of anadrol in. But seems that 25 / ml is still not holding per @Whistles77 experience.
Looks like it's not far off holding though. I can play a bit if you'd like....for science. If i add 4ml more TNE, then i'll have 16ml of TNE 29.8mg/ml, Anadrol 20.2mg/ml. That'd be usable for me.
 

Attachments

  • IMG_9444.webp
    IMG_9444.webp
    1 MB · Views: 12
Looks like it's not far off holding though. I can play a bit if you'd like....for science. If i add 4ml more TNE, then i'll have 16ml of TNE 29.8mg/ml, Anadrol 20.2mg/ml. That'd be usable for me.
I think it will hold at some lower concentration. The practical issue as I see it is making sure the blend holds for a few days at room temp prior to pinning it, otherwise we'll end up with the same problems we had from the anadrol itself in terms of PIP, delayed injection site reactions, etc. if it re-crashes post-injection.
 
I think it will hold at some lower concentration. The practical issue as I see it is making sure the blend holds for a few days at room temp prior to pinning it, otherwise we'll end up with the same problems we had from the anadrol itself in terms of PIP, delayed injection site reactions, etc. if it re-crashes post-injection.
Agree. I'll see how this one goes. I'm kinda optimistic this will be usable already....although there's zero chance i'll be doing any room temp pins.
 
This is helpful. I see the anadrol is down to about 10 mg / ml in each. That's quite the dilution but that may be what it takes to hold. I would hope to get it to at least 15 mg / ml so that a 2 cc pin would get at least a decent amount of anadrol in. But seems that 25 / ml is still not holding per @Whistles77 experience.
I was forced to only use 8ml of the anadrol since 2ml was severely crashed. I was able to salvage the remaining anadrol for the smaller 10ml vial blend.
 
So how do you decide which to use.
I like the right one more but the left does have dbol in it.
Thats actually a good question, i need to test drive them this weekend. I have a bulletproof vts smith machine attachment for my rack setup that will be used for the first time this weekend, so this is a perfect cause for celebration. I’ll try the one with m-tren first. Haha.
 
Back
Top