MESO-Rx
Anabolic Steroids
MESO-Rx Sponsor AASraw: GMP-Certified Steroid and Peptide API Manufacturer
- Thread starter AASraw
- Start date
Motojager
Member
I was just showing the simple math. Target mg, divided by percent of compound, times what ever % extra you want to add.= amount needed
Basically the same as you did above in a simple form.
The-Squat
Subscriber
That's what I thought, wasn't calling you on it. I wasn't sure if I came across clear in the original post.
Been a long day in the lab and will be another tomorrow lol.
What do you suggest as the most accurate method ? I thought weighing a known volume of oil was a better solution than beakers . And I figured syringes were also accurate . Open to suggestions
I'm trying to contribute here and spend time with my lady at the same time. I'm failing on both fronts lol
The-Squat
Subscriber
Graduated cylinders
Graduated cylinders
Attachments
The-Squat
Subscriber
So my batch that tested 99% with AB that we can consider 98+, I'm going with 96% on the caution side. Still not use to seeing 99%, which is most likely 98+. It's not a big issue to me.
Even though the look is different a tad and a brighter tint than usual, it's very clean, it is pumping through the filters as usual.
This must be the cleaned up batch or post no melt batch or the no melt batch was something else, since nobody will test it we will never know.
Even though the look is different a tad and a brighter tint than usual, it's very clean, it is pumping through the filters as usual.
This must be the cleaned up batch or post no melt batch or the no melt batch was something else, since nobody will test it we will never know.
Motojager
Member
What are you considering no melt batch?
The-Squat
Subscriber
I think it was the 1st batches made and shipped with the pre orders, I waited for pro order to end.
It's hard to tell about the test c no melt without any tests done on the raws.
Could have been the wrong items shipped as it was crunch time.
Motojager
Member
It tested at 95. 11/28 batch.
Last edited:
The-Squat
Subscriber
At one point the filtering slowed down a bit, still going just slower.
This is not normal and goes along with the filtering issues.
This is not normal and goes along with the filtering issues.
Defiant Pharma
Subscriber
Are you using polycap(capsule filters) or bottle tops?
Just curious because I haven't noticed anything out of the ordinary filtering through my polycaps with these recent batches of Test C from them. Finished product is a little more yellow tinted than normal but thats about it.
dcfreak
Member
My latest batch also has a slight yellow tint to it compared to a previous batch of raws that brewed clear.
Jano tests should be ready next week on both batches
Jano tests should be ready next week on both batches
The-Squat
Subscriber
Bottle Top Millipore
Everything is normal, even the filter is clean looking just slow.
My take is this batch was a fixed no melt batch, makes sense to me.
Was your powder a shade darker of white than usual?
Thank God the pump has it going and looks like I'll be fine but as others have reported, will take a bit longer.
I will just from this point on mix a little of the stuff with the other stuff I have each batch.
2000ml yesterday took 2.5hr of other stuff, 2000ml today I'm at 2hr and 1/3 of the way done. Today mixed almost half with the other stuff. So there is that as well!
The test 100ml I made to see if it would melt didn't crash, so that's another good sign, that didn't get filtered until yesterday when added to different raws.
I'll just stretch this stuff out for now on, but most don't have the luxury to do so.
I'm sure I'm a lot smaller than you as well, just private with faithfuls for 15 years that also refer others.
Similar threads
