Need to know if this is normal, help needed

[Saphir]

Just curious if this is normal , I did a test E , tren E and Reta order from driada , on the 2nd week my test E just crashed full of crystals even after heating it on the oven and full of bubbles as soon as I put the needle on , same thing with the tren E vial and last injection I did gave me pip with a lump on glutes for 4/5 days , and the Reta let’s just say it squirted/leaked 50% of the product outside randomly

 

[Cyp180]

Heated in oven ?

 

[Saphir]

Heated in oven ?

Yes, pre heat oven for 15 minutes at 80• then put vial for another 15/20 minutes

 

[Saphir]

Heated in oven ?

I mean technically I don’t see how something should crash after 2 weeks , always at room temp and no sunlight at all

 

[oldgrey]

Not really a concrete answer, but no that doesn't seem normal at all. Do you live in alaska (kidding, kinda)? Unless you have like extreme temps or its like a test600 mix thats pretty odd on the test crashing imo.. bubbles could be due to vacuum / pressurizing from heating but you would feel the draw pressure with the plunger i would assume?

I once had a vial of tren that kept crashing, and after having to heat it a few times it became unusable, even .1 ml IM or sub q would result in extreme PIP, so I just tossed it. Likely became oxidized from the heat, or some reaction with the heat caused a change.

 

[Panzerchocolat]

Having your bedroom window open to air could be enough for the test to crash.
Avoid the oven if you don’t know the material of your stopper. I always boil some water, add the water to a egg holder, place the glass vial in it avoiding the stopper, shake after 10 seconds, place it back and repeat.
The bubbles seems to form due to vacuum, do you inject air before pulling your test?

 

[Saphir]

Not really a concrete answer, but no that doesn't seem normal at all. Do you live in alaska (kidding, kinda)? Unless you have like extreme temps or its like a test600 mix thats pretty odd on the test crashing imo.. bubbles could be due to vacuum / pressurizing from heating but you would feel the draw pressure with the plunger i would assume?

I once had a vial of tren that kept crashing, and after having to heat it a few times it became unusable, even .1 ml IM or sub q would result in extreme PIP, so I just tossed it. Likely became oxidized from the heat, or some reaction with the heat caused a change.

I live in Europe , is Test E 250mg/ml and a tren E 200mg/ml

 

[Saphir]

Having your bedroom window open to air could be enough for the test to crash.
Avoid the oven if you don’t know the material of your stopper. I always boil some water, add the water to a egg holder, place the glass vial in it avoiding the stopper, shake after 10 seconds, place it back and repeat.
The bubbles seems to form due to vacuum, do you inject air before pulling your test?

I put all my vials inside a small box no sunlight, and no I don’t open the window, I don’t even pull the test I just stick the needle and it just produces mass bubbles and yes I inject some air always

 

[Crx221]

I've seen more gear crashing with the temps dropping which is annoying. Just heat it up and put it into a sterile vial.

 

[Elektrobot]

Reta let’s just say it squirted/leaked 50% of the product outside randomly

Did you receive it already reconstituted?

 

[Burly]

@Driada Medical

 

[Psychokoak]

Having your bedroom window open to air could be enough for the test to crash.
Avoid the oven if you don’t know the material of your stopper. I always boil some water, add the water to a egg holder, place the glass vial in it avoiding the stopper, shake after 10 seconds, place it back and repeat.
The bubbles seems to form due to vacuum, do you inject air before pulling your test?

The method is very good and it has always worked. Heated in water then shake and repeat this several times.

@Saphir
Bubbles in oil when you inject air inside are normal
What does your reta look like? I have already had the problem of a dissolution. I just had to roll the vial in my hand for 5 minutes for the mixture to do well or add a bit more of water.

As long as you don't get a jellyfish inside, it's good.

 

[Saphir]

The method is very good and it has always worked. Heated in water then shake and repeat this several times.

@Saphir
Bubbles in oil when you inject air inside are normal
What does your reta look like? I have already had the problem of a dissolution. I just had to roll the vial in my hand for 5 minutes for the mixture to do well or add a bit more of water.

As long as you don't get a jellyfish inside, it's good.

Hey, Reta is already over , since half of it squirted outside the vial and is not about the bubbles tho is just that their stuff is getting crystal’s after 2 weeks,

 

[Saphir]

Did you receive it already reconstituted?

Not, I did it with an insulin syringe, when I pulled the syringe out a bunch squirted outside, I let it rest/disolve , and when I flipped the vial so I could draw the product another bunch started leaking from the vial and I didn’t even injected

 

[Psychokoak]

Hey, Reta is already over , since half of it squirted outside the vial and is not about the bubbles tho is just that their stuff is getting crystal’s after 2 weeks,

The reta you put too much air in it then
The first time I reconstituted a small vial of gh I put 1ml of water with same of air and everything go out because of the pressure lol. 20€ Squirt
The trick next time is to put your water on and before removing the needle you suck in air. It will take the pressure off the inside.

Crystallization sometimes happens. Before or after the opening, it doesn't matter. A "cold" and it can happen. From memory, Driada doesn't use that much solvents.
It's a good thing for your health but it makes the product capricious sometimes. We have to cook again. This is quite well known in the PED community.

 

[Psy-chonaut]

Not, I did it with an insulin syringe, when I pulled the syringe out a bunch squirted outside, I let it rest/disolve , and when I flipped the vial so I could draw the product another bunch started leaking from the vial and I didn’t even injected

Every indicator tells me, that You didn't equalise the pressure, both in the peptide vial -> and from Cold to Hot in the oil vial....

Lots of of posts with same problem as you have.....

Just pin it with a needle / or pull the plunger out while the needle is in between the bac-water and the top - voila, air will slip in, and pressure is alligned= no more erotic squirts !