First Brew Complete

[zmurphy]

I made 2 things:

400mg/ml Test D
200mg/ml Test P

Both 1.5BA/30BB in Castor oil. The Test D went like a dream. It fell into solution without solvents and minimal heat. It filtered super easy. But I started with the Test P and that was less awesome. Took awhile and more heat that I would have preferred to get into solution and took FOREVER to filter. Looking things over afterwards I found a piece of foam between the plate on the scale and the base left over from the packing material. So the weight of the powder was almost certainly reading low. Its definitely overdosed, potentially by ALOT. Any guess on the max solubility of Test P in 30% BB? The solution is holding so its under whatever the limit might be. Lesson learned.

I'm going to send them out to be tested in a blend of .5ml of Test D and .5ml Test P. That should yield a concentration of 200mg/ml Test D and 100mg/ml Test P.

 

[IndividualMan]

scale trouble, rookie mistake.
the mixing before testing is a good idea to save some money. You should def get it tested just for peace of mind.

 

[zmurphy]

scale trouble, rookie mistake.
the mixing before testing is a good idea to save some money. You should def get it tested just for peace of mind.

Yea I have no interest in running either of these until I know whats in them.

 

[anubisascended73]

I made 2 things:

400mg/ml Test D
200mg/ml Test P

Both 1.5BA/30BB in Castor oil. The Test D went like a dream. It fell into solution without solvents and minimal heat. It filtered super easy. But I started with the Test P and that was less awesome. Took awhile and more heat that I would have preferred to get into solution and took FOREVER to filter. Looking things over afterwards I found a piece of foam between the plate on the scale and the base left over from the packing material. So the weight of the powder was almost certainly reading low. Its definitely overdosed, potentially by ALOT. Any guess on the max solubility of Test P in 30% BB? The solution is holding so its under whatever the limit might be. Lesson learned.

I'm going to send them out to be tested in a blend of .5ml of Test D and .5ml Test P. That should yield a concentration of 200mg/ml Test D and 100mg/ml Test P.

Just made some Test D at 500mg/ml in mig 812 with 2%BA and 25% BB. Raws tested by Jano at 98.7%. Smooth as butter when injected, zero pip after 72 hrs. This will be my go to with far reduced injection volume. Went off an NIH.gov study of solubilty.

 

[zmurphy]

Just made some Test D at 500mg/ml in mig 812 with 2%BA and 25% BB. Raws tested by Jano at 98.7%. Smooth as butter when injected, zero pip after 72 hrs. This will be my go to with far reduced injection volume. Went off an NIH.gov study of solubilty.
View attachment 378796

I was thinking about 500mg/ml, but chickened out in the end. I should have done it because I could have just diluted it if i got pip. Next time....

I'm blown away that Test D isn't more popular. It really should be the most popular ester, especially with the pippy Test E raws and Test C only going to 250mg/ml.

 

[IndividualMan]

I was thinking about 500mg/ml, but chickened out in the end. I should have done it because I could have just diluted it if i got pip. Next time....

I'm blown away that Test D isn't more popular. It really should be the most popular ester, especially with the pippy Test E raws and Test C only going to 250mg/ml.

test C goes to 300mg/ml in MIG812. also no PIP 275mg/ml in castor

 

[anubisascended73]

test C goes to 300mg/ml in MIG812. also no PIP 275mg/ml in castor

It does and will crash below 50° and needs to be reheated.

 

[IndividualMan]

50°F i hope, otherwise mine is defying physics