Charge me double and I will buy 50 cartons
MESO-Rx
Anabolic Steroids
Dutch Labs - EU Domestic
- Thread starter Dutch Labs
- Start date
Dutch Labs
Subscriber
Janoshik responded that they now use their own standardised test and it's no longer experimental. Cost $380
OilCarrier
Member
The rate of degradation with exposure to oxygen and light is so high for telmisartan that it would not be reliable for users to keep any quantity in a bottle. It's true that there are other ugl's doing this and that their telmisartan still works to some degree, however the effective dose one is taking is drastically lowered depending on the time it has been exposed to oxygen.
For efficacy, 40mg telm still has a beneficial effect on users normally taking a 80mg dose. So a degraded 80mg dose might still give the benefits that a normal 40mg dose would give. However that still doesn't mean it's a good idea to keep telm outside of aluminum blisters in any case.
For efficacy, 40mg telm still has a beneficial effect on users normally taking a 80mg dose. So a degraded 80mg dose might still give the benefits that a normal 40mg dose would give. However that still doesn't mean it's a good idea to keep telm outside of aluminum blisters in any case.
Kralteramon
Member
Hi @Dutch Labs , one of my Test C vials is leaking pieces of stopper into the oil. This vial even has a big chunk in it. What to do?
Kralteramon
Member
DugPrime
Member
use a sterile (pharma-grade) PTFE filter.
Kralteramon
Member
It won't filter out the liquified silicone byproducts. My guess is that this piece of silicone will dissolve in a few days... I'm not comfortable to inject this.
you sure it's not crashed? because that's what it seems to me
Kralteramon
Member
Yes i'm 100% sure i saw it detach from the bottom of the stopper and float down. It was gelly and it melted off since my last injection and stuck to the stopper and side of the glass.
Looks like a crystal yes
Kralteramon
Member
You can see more pieces clinging to the glass and the stopper is bulging where it detaches.
Test C is not high solvent brew so it's very odd to melt the stopper even if it's silicone, I never seen a stopper melting the way you are telling us. Not saying it's not true but the picture looks like crashed gear.
Crashed gear stuck to the stopper that decreased and just melted again.
As you aren't injecting it, open the vial and take the allegedly melted stopper out? Or just wait for dutch labs to answer you
My tne has same look when crystalised.
Kralteramon
Member
Yeah let me check maybe i just bacame paranoid but it does look weird that it stuck from there. Never happened before.
Kralteramon
Member
Inspected the stopper, it seems to be intact. Weird that it happened to be attached to the stopper and became like gel. But that's probably just my inexperience. False alarm everyone!
Dutch Labs
Subscriber
It's crashing. I've seen it before, that the crystals grow on the stopper.
To fix it, can heat the vial in an oven for ~40 min (60 - 70C) and shake in between and afterwards. After that it should stay dissolved a long time on room temp.
This Test C batch crashes sometimes during transport or just over a long period of time standing still. You're not the first person to contact me about it. Sorry for the issue. I've adjusted the recipe to prevent this.
As for the stoppers, ETFE coated stoppers are used since last month for all new batches.
Last edited:
Den84
Member
It’s crashed.. very common when test C is dosed 250 mg ml or more
Yes, but I think it's also a question of solvents. I've used many CYPs from China, many 250mg crashes, and many others are perfect.
In the EU, however, in winter it's always crashes.
Similar threads
Sponsors
Latest posts
-
-
-
-
My regaining fertility after TRT log- Latest: eryximachus
