Kingshit108
New Member
I believe this creates 1mg/ml test p..
If you wanted to add bb/ba for safety and ease of inj you could replace some of the grapeseed oil with your solvents and detergent
MESO-Rx
Anabolic Steroids
Diluting and Filtering Oils for Female Doses
- Thread starter mok4315
- Start date
If you wanted to add bb/ba for safety and ease of inj you could replace some of the grapeseed oil with your solvents and detergent
bananafeet
Member
100mg of test p * 1ml = 100mg total
1ml (100mg/ml) + 9ml (0mg/ml) = 100mg/10ml
= 10mg/ml
BigDadd7
Member
And he didnt include any accommodations for filtering the gso or adding ba.
Kingshit108
New Member
You are right my bad math
bananafeet
Member
All good bro. My math ain't great either
mok4315
Member
Except for the math, that is essentially what I did with a couple small differences.
The first is that I divided the whole vial into 5 cycles, though that totally isn’t necessary. I only did it because I don’t trust UGL vials to be good quality and last for several years.
The second difference (which turned out to be a bitch of a difference) was the filtering. The amount lost in filtering may not matter a lot to someone who takes large doses at high concentrations but, and I can’t stress this enough, it impacts women to a far larger scale. If we don’t know the exact concentration, it can mess up our whole cycle in a big way. Either we’re underdosing (best case scenario) or overdosing (and we risk not knowing until it’s too late). Hence the meticulous calculations. If I were to update this guide, I’d just filter the whole vial into a sterile reputable one and not give a fuck about how much is lost, then do the diluting into smaller vials from there.
Kingshit108
New Member
Ok I know all my reputability went out the windows with my bad math but..
First filter some grapeseed oil
Make 2x 9ml vials..
Draw 1ml of 100mg/ml test p
Insert into a 9ml GS vial
Shake
Draw from 10mg/ml vial
Insert into inert 9ml grapeseed vial
Should produce 1mg/ml vial
Then you have
1x 1mg/ml -10ml vial
1x 10mg/ml -9ml vial <- this is your feeder
Whenever you need to create a new 1mg vial. Just Draw from your 10mg/ml
And yeah I have envied women in the sense that this is all basically free for them.. but also the dosing issues become 100x more of an issue.
My homebrew is basically just me saying fuckit close enough.. I think my last test C cook was like 333mg/ml cause I judged the math a few times
Kingshit108
New Member
If you wanted to add BA and BB you just subtract it from your grapeseed
Stealth500
Member
-2 snap vials testoviron
-7.8 ml miglyol
-0.2ml BA
draw into 10ml syringe,squirt through sterile filter into sterile vial.
result = 10ml with 500mg test.
This should work no?
-7.8 ml miglyol
-0.2ml BA
draw into 10ml syringe,squirt through sterile filter into sterile vial.
result = 10ml with 500mg test.
This should work no?
There is gapless syrings on aliexpress for cosmetic purposes and they go as high as 32G. But yeh you generally can lose 0.05ml which definately adds up.
Currenlty i pull in an 0.05 air bubble on a 1ml syring and inject daily, (23g draw, 30g inject) set that to the plunger and inject. Being doing that for almost a year with no issue.
Currenlty i pull in an 0.05 air bubble on a 1ml syring and inject daily, (23g draw, 30g inject) set that to the plunger and inject. Being doing that for almost a year with no issue.
