AryanonLifta
New Member
So Telegram will return then? I enjoyed bullshittin’ with the bros
MESO-Rx
Anabolic Steroids
RockyP
Member
Are you using the primoTest 250 or separate primo and test? What are your E2 levels on that stack? I started it a few weeks ago and will be pulling labs in a month.
No, I am running the Test C 300 blend and Primo 200 blend. My E2 at 300/200 split dose is 15.6 as of 4 days ago. Planning on raising Test dosage this week to help boost my E2.
RockyP
Member
oh boy - that's the same ratio i'm running as well - I'm a high aromatizer so I will wait for labs but I have some extra test on hand to adjust. Thanks for sharing!
Telegram is up. Are you clicking link in our email to join?
Anyone run any of Axle's Test Prop 200? For the life of me I cannot get my vials to stop crashing. I have four vials and each of them keeps crashing no matter what. I don't keep them in the cold and have even left them in mounds of blankets to still wake up to them crashed. Even worse I can't fully get them to go back into solution with boiling water. No matter how many cycles of sitting in boiling water and shaking, there's still shards floating around.
BP_6
Member
Well, not going into the PiP that would likely cause. 200mg/ml test prop. Yea, that isn't going to be easy to hold. The two reasons above is why you rarely ever see it.
Ateam2023
Member
i bet that test p @200 mg/ml will give some serious PIP,, Good luck running that for any amount of time, and all those frequent "necessary pins" , ouch,,
Actually I've been exclusively running it for probably close to 6ish months now. Frequent injections don't bother me and it doesn't give me PIP at all. Just for some reason this recent batch refuses to hold when I've had no issues with previous orders.
SwolieGuacamole
Member
What makes you stick to prop? Quicker saturation? Drier?
Initially started out to try all short esters on a blast and just decided to stick with it instead of transitioning back to test e. I do notice I hold a bit less water and don't plan on stopping daily injections so it works for me. Though after I finish what I have left I'll probably transition back to test e or at least a lower concentration of prop if the crashing is gonna continue to be a problem
Where’s the TG link?
Oldhand
Member
You can always try the oven. Set the oven above boiling point since you already know that’s not hot enough.
If you’ve never done it this way before, put a pin in the stopper to vent the vial. Just make sure the needle is above the oil in the air gap. This will allow the vial to vent without suctioning up any oil as things expand from the heating process.
AryanonLifta
New Member
Went back to email and rejoined. Thought it went away… I opened TG one day and it was just gone. Thanks
bigdaddyandfriends
Member
That's why prop200 isn't commonly made. How much are using per day? Switching to something that holds in solution at that or even higher concentration (cyp, enanth, iso) or a mix like Sust will make more sense, even if you have to use a tiny bit more oil because of the added ester weight.
Boiling water work poorly in my experience. Hair dryer does better. Best, get a mug warmer from amazon for $10-15. Use it on middle temp - for mine its 162 degrees. If it's crashed, leave it on until it's redissolved which takes a little bit, so stick a needle in the top to vent it.
And even if it doesn't look crashed to the naked eye, heat it briefly before injecting - that will likely eliminate the PIP. Mixing it with other more dilute compounds helps too. The PIP is from microcrystals that you are injecting, they are not visible but effectively make the oil a suspension. If you have used test or winstrol suspension, it's probably a very similar feeling although likely not as bad. As time goes on those microcrystals act as a nidus for more product to precipitate out and clump on, eventually resulting in the crashed appearance. It's the same as a child's crystal making science experiment, basically.
I do the same thing for DHB100, Primo200, and TNE50. All used to cause some PIP, warming before injecting eliminates it. Other things I use hold better and don't require warming. And mix everything together for a single daily oil injection, typically 4-5 compounds that I fit into a slightly overloaded 0.5cc syringe.
I do separate, typically subQ injections for the water based stuff I used (GH, HCG, MOTS, SS31, Reta, BPC157, TB500, CU-GHK, L-carnitine). High volume water based injections into muscle aren't a great idea because of the infection risk, and ultimately it ends up in the same place whether IM or subQ.
Tbaz192
Member
It shouldn’t. Unlike the Chinese sources that sneak it in.
No.
You’ll see the link to join on the signature of our email responses.
Oldhand
Member
I’m on Axle’s primo 200 right now- no EO.
I’m running it with Test 500 and NPP 200. 1ml of each every 3.5 days.
It is pretty smooth considering these are all high concentrations. Just make sure you spread out injection sites. Slin needles are great for this.
Similar threads
