dinfar1337
Member
205c needed for benzyl alcohol to evaporate at a significant speed
as long as you're not brewing the same ba for 20 days over or using 500c for your brew its better to add ba in start for sterility
MESO-Rx
Anabolic Steroids
MESO-Rx Sponsor AASraw: GMP-Certified Steroid and Peptide API Manufacturer
- Thread starter AASraw
- Start date
as long as you're not brewing the same ba for 20 days over or using 500c for your brew its better to add ba in start for sterility
Brewed a trial vial of TNE 50 with MCT last night. Wasn’t able to dissolve raws at all when I put it in liquids which did not surprise me.
It did dissolve after I melted the raw first for 2 mins with the warmed liquids after. It is starting to recrystallize this morning as expected… was hoping to avoid EO, but what advice would y'all have for keeping TNE dissolved in solution?
It did dissolve after I melted the raw first for 2 mins with the warmed liquids after. It is starting to recrystallize this morning as expected… was hoping to avoid EO, but what advice would y'all have for keeping TNE dissolved in solution?
Photon
Member
2/40
i bought the exact hot plate with mag stirrer from the recommended homebrew shopping list, so i have the ability to control temp accurately damn thing was almost 200$ it better be accurate. also invested in a nice vacuum pump and lab stand setup for filtering into pre-sterile vials. since its only for personal use it doesnt matter to me if i flip the tops off already, i already know what ima put inside hehe. id be willing to learn the temps and all that, but since im a few weeks out i dont mind waiting and then revisiting in the homebrew section. that said i do appreciate the advice.
The-Squat
Subscriber
Only time I don't add BA 1st and do it last is withTren A, otherwise dump the raws in a beaker add BA add BB and then turn on the spinner and heat. Add warm oil to dissolved raws and spin more.
I leave it on 120F to 130F to stay warm during the filtration process on large batches which is all the time for me.
All this rocket science is pretty funny don't you think? LOL.
The-Squat
Subscriber
There is more than 1 way to skin a cat, if it works for you it works but I'd never heat the raws 1st alone without BA and BB especially Tren A, but my batches are larger than most.
What’s a lab stand setup consist of? Interested for exact same scenario for self brewing.
Photon
Member
dcfreak
Member
Do you have any recommendations on a specific caulk gun? My thumbs are interested
identical to the one i ordered
Venom Lab
Subscriber
Man reading some of these ppl description on how they brew make me laugh hysterically.
Warm this, while you warm in another container this then you add that to this and then you warm the other thing, all at the same temperature, add that, no more swirl? OK add that one too bla bla. Bla.
What the fuck?
Are you all wrong in the head?
BA doesn't evaporate at the temperature we use, it doesn't even get close to the fume temperature.
Have you ever used Google?
I guess not.
Just dump everything in the beaker warm and stir. Job done.
There is no based science logic behind the crap I have just read in the last two pages. At best one could leave the carrier oil outside before the raw are dissolved properly just for complicated substances so you avoid to keep the carrier oil at XX temperarure for a long time.
Except for that, God damn stop complicating something that is not complicated.
They do the beaker to beaker dance but don't test their raws. Brilliant
AlexDavis43
Member
Damn, Venom coming in hot
The-Squat
Subscriber
Right?
Hurts my head as well, it's not that hard, I just don't like adding carrier in until raws dissolve in the BB and BA because when making large batches of stuff like Test C it can take so much longer. Melt then add warm oil and homogenize. Only reason I warm the oil is so it all stays warm enough to filter, some can't even figure out that part either.
I wish vendors would just start only providing to those that can rather than those that waste what's hardly there.
I'm almost done reading this shit and can't help in other threads because as a subscriber I don't have the privileged lol.
Right?
Hurts my head as well, it's not that hard, I just don't like adding carrier in until raws dissolve in the BB and BA because when making large batches of stuff like Test C it can take so much longer. Melt then add warm oil and homogenize. Only reason I warm the oil is so it all stays warm enough to filter, some can't even figure out that part either.
I wish vendors would just start only providing to those that can rather than those that waste what's hardly there.
I'm almost done reading this shit and can't help in other threads because as a subscriber I don't have the privileged lol.
The-Squat
Subscriber
It does get annoying, and to be honest it takes time for most to find their groove and see the simplicity.
AlexDavis43
Member
My brewing mentor, El Luchador, sends his regards and a note reminding the phrase 'keep it simple, stupid'
*as witnessed by Omar Little aka Chalky White (reference)
AbstractMind
Member
Still no word on Mast P .. sick ..
AASraw said make new order 4kg TC and they refund 500gr
so no refund
Remind I ordered 6kg test cyp
I received 2kg not dissolved and 2kg test prop
and 2kg TC still on the way
That's Axel bro.
December logistic performance for your reference:
US: 100% pass rate
UK: 100% pass rate
Australia: 98% pass rate
Canada: $96% pass rate
EU: $100% pass rate
New Zealand: $100% pass rate
Spring Festival is coming soon and the existing stock become less and less.
US: 100% pass rate
UK: 100% pass rate
Australia: 98% pass rate
Canada: $96% pass rate
EU: $100% pass rate
New Zealand: $100% pass rate
Spring Festival is coming soon and the existing stock become less and less.
Similar threads
