Mixing compounds into single vial questions

[LumpLard]

I am going to be putting TEST E 250mg/ML and DECA 400mg/ML into a 10ML vial to start small then end up moving up to 20-30ml vials for longer usage per vial.
TEST is MCT and DECA is GSO not sure if that will affect since I have no idea if they’ll “combine” I have read they create a homogeneous mixture.
I want to make sure that I’m not special needs, aswell as the dosing will be correct.
7.5ML of T 250 (1875mg total)
2.5ML of D 400 (1000mg total)
1.5 ml twice a week = 3ml totaling dosing to 562.5mg TEST and 300mg DECA. I feel like I’m right but I always make sure and get multiple opinions before moving forward.

 

[Dial It In]

They will be fine together. Just be accurate as possible to get your dosing correct. Make sure you have the right setup so you don’t contaminate your mix. If you are going into an empty vial it needs to be sterile among other things. Use the correct filters. Of course this is for safety. If you don’t care then do whatever you want. Just a harm reduction forum.

 

[BigDadd7]

They'll be fine. I recommend heating the mix up on a coffee cup warmer and inverting a few times before drawing. Some layering may occur while storing.

 

[Dial It In]

They'll be fine. I recommend heating the mix up on a coffee cup warmer and inverting a few times before drawing. Some layering may occur while storing.

Almost like oil and water

 

[BigDadd7]

Not

Almost like oil and water

Not quite that bad. They will remix just fine with a little heat and mechanical energy. I definitely wouldn't draw from the vial cold and unagitated.

 

[Eddie.]

Oils will homogenise whatever the carrier is. I’ve mixed more than 2-3 different carrier oils and never had an issue.

I don’t filter the oils, I just draw, transfer the desired amounts, heat it and give it a good shake. Also, you better heat and shake it couple times before each use.

 

[Ghoul]

I definitely wouldn't draw from the vial cold and unagitated.

Start by drinking a cup of coffee while reading some of the shit people say on MESO and you won’t be cold or unagitated.

 

[BigDadd7]

Start by drinking a cup of coffee while reading some of the shit people say on MESO and you won’t be cold or unagitated.

Lmao. That is solid advice!

 

[Dial It In]

Not

Not quite that bad. They will remix just fine with a little heat and mechanical energy. I definitely wouldn't draw from the vial cold and unagitated.

I know was just the best visual pic I could give

 

[Dial It In]

Start by drinking a cup of coffee while reading some of the shit people say on MESO and you won’t be cold or unagitated.

Start by drinking a cup of coffee while reading some of the shit people say on MESO and you won’t be cold or unagitated.

Something in particular wrong with the visual pic I was trying to paint to describe layering? Wasn’t sure why that was amusing.

 

[Ghoul]

Something in particular wrong with the visual pic I was trying to paint to describe layering? Wasn’t sure why that was amusing.

No man, laughed because I read that as a witty comment. Sometimes the humor is so clever it goes over our own head lol

 

[Dial It In]

No man, laughed because I read that as a witty comment. Sometimes the humor is so clever it goes over our own head lol

Lots of dudes smarter than me around here. I only try to offer advice on things from my own experience. I’m not always right and not always wrong. But what I do try to do is understand the audience and keep replies and comments simple with the understanding some might not grasp that high level explanation. Lots of people read things and never comment out of fear of being chastised or even ask questions out of the same fear. So if I can relate things to what 99 percent of the population has been exposed that is the route I take. Perhaps my methods aren’t the cup of tea people prefer but I think some appreciate the simplistic approach. Anyway, thanks for clarifying.

 

[Zebedee]

I am going to be putting TEST E 250mg/ML and DECA 400mg/ML into a 10ML vial to start small then end up moving up to 20-30ml vials for longer usage per vial.
TEST is MCT and DECA is GSO not sure if that will affect since I have no idea if they’ll “combine” I have read they create a homogeneous mixture.
I want to make sure that I’m not special needs, aswell as the dosing will be correct.
7.5ML of T 250 (1875mg total)
2.5ML of D 400 (1000mg total)
1.5 ml twice a week = 3ml totaling dosing to 562.5mg TEST and 300mg DECA. I feel like I’m right but I always make sure and get multiple opinions before moving forward.

The difference in viscosity between MCT & GSO is much much less than that between propylene glycol (PG) & vegetable glycerin (VG), which are the two main ingredients used in practically all e-cigarette eliquid. VG/PG ratios in eliquid usually range between 50:50 to 70:30 & vigorous shaking for a couple of minutes is all that’s required to create a homogeneous blend.

A key requirement for good blending is ample headspace in the vial - you need at least 10%, with between 10-20% obviously being better.

Heat isn’t necessary - pretty much no eliquid homebrewer or manufacturer uses heat to blend VG & PG because it can negatively affect the nicotine.

Best to give the vial a damn good shake before you draw, to re blend any minor layering that occurred. Again this is what eliquid manufacturers recommend. I say minor because in coloured eliquids, the colouring element is always PG. If anything more than minor separation / layering / stratification occurred between the coloured PG & clear VG, you’d be able to see it through inconsistent colour, but I’ve never seen that in around 15 years of vaping.

 

[LumpLard]

They will be fine together. Just be accurate as possible to get your dosing correct. Make sure you have the right setup so you don’t contaminate your mix. If you are going into an empty vial it needs to be sterile among other things. Use the correct filters. Of course this is for safety. If you don’t care then do whatever you want. Just a harm reduction forum.

How would I go about filtering? I will admit I have no experience in that area.

 

[Dial It In]

How would I go about filtering? I will admit I have no experience in that area.

Thread 'Filtering finished oils'

Jan 5, 2025

I see a lot of great posting lately on filtering finished oils. Decided to make a thread to hopefully consolidate all the great info in one spot.

My knowledge is somewhat amateur on this topic, but what I know so far is that for the average user buying 10ml UGL finished oils a PTFE 0.22 13mm Is likely the best choice.

If you have good info on filter types, brands, techniques, etc. I want to know!

• UncleBuns
• Replies: 695
• Forum: Steroid Forum

•