homebrew water based winny

[steroid500]

does anybody have any experience with homebrewed water based winny? Mine separates out within a day and clogs the pin when shooting, even after shaking it.

Recipe is:

10g winny powder
95ml bac water
5ml polysorbate 80

..i know, i know i shouldve used peg400 too, but is there a way to better stabilize this? ive been shooting with 22g and they still clog, dont wanna jump to 18g ::shudders::

 

[bigbench]

Bro, just drink the shit. It will work the same for ya! Heating it will help SOMEWHAT, but like you said, you should have used peg400!

 

[steroid500]

thought about that, but if you remember, im logging using capoten, albuterol and yohimbe for fat loss. the capoten stresses the liver as it is (which is why you cant use NSAID's for headaches) and winny is the hardest on the liver.

i know man, im fuckin pissed about it. i did the research on making water based, but forgot about peg and jumped in thinking all i needed was tween80 and bac water, trust me, i already beat myself up for that

 

[Lizard King]

Found this for you, not sure if it helps you now though:

Water Based Winny
by DougoeFresh

This hormone has a screaming high melting point. For this conversion solvents will be used to bring the stanozolol into a clear solution for filtering and titration. The final result will be a suspension.

Items needed for a 1 gram conversion:
1 Gram winny powder
4.0cc PEG 300/400
0.45um syringe filter (2 quantity)
0.6ml polysorbate 80
0.4ml benzyl alcohol
14.25ml distilled water
Beaker
20ml vial
20g pins
5ml syringe
10ml syringe


1. Mix 14.25ml of distilled water with 0.4ml benzyl alcohol.
2. Pass through syringe filter into 20ml vial.
3. Put 2ml PEG300/400 into beaker and add 0.6ml of polysorbate 80.
4. Add 1 gram of stanozolol powder to PEG/ps80 mix.
5. Heat until stanozolol clears. The heat will be very high, PEG may smoke. This is ok.
6. Allow stan liquid to cool.
7. Draw into 5ml syringe, run it through the second new syringe into the 20ml vial containing our steralized water.
8. NOTE: You can use the same syringe filter as long as the filter is completely dry.
9. As you filter the PEG/ps80/Stanozolol mix through the filter into the water it will titrate back into micronized form in the water. When this is done shake vigerously.
10. Run 2 more ml's of PEG300/400 through filter to purge.


This conversion results in 20ml - 50mg/ml sterile water based stanozolol suspension for injection.

Additional Note: After much experimentation I have found that ps80 is NOT needed. However, I have a contact who makes large volumes of this, and has found that about 1 out of 10 conversions will clump for some reason. Adding ps80 alleviates the problem, so to avoid this I have included it in the directions

 

[bigbench]

Well not to make you feel worse, but injecting it stresses the liver just as bad. Its the same chemical either way its inserted into the body and will pass through the liver the same way eventually. Make sure to get on some liv52, milk thistle and R-ALA (one of the best for your liver and antioxidants as well)

 

[steroid500]

i knew it was going to hit my liver, but thought it wouldnt be as bad as oral, but thanks for the suggestions.

thanks lizard, ya talk about a day late and a buck short! needless to say, i will be sticking to oil based homebrew from now on, so much easier to deal with.