Hopefully you'll like the 100mg/ml version just as much or more! haha
MESO-Rx
Anabolic Steroids
Arail Pharmaceuticals - US Domestic
- Thread starter Arail
- Start date
Crizcrae
New Member
Are we still waiting on Jano to retest the TNE 100?
nutcase6174
Member
same. var gives me a bigger strength boost than even superdrol. now sdrol gives that superhero-like fullness, but var's strength and vascularity literally make it my top drug. too bad it skyrockets my ldl, otherwise id run more frequently.
AllGoodThings
Member
Anyone else struggling to get the Anadrol back into solution? I was at 183°F for about 15 minutes, bumped it up to 196°F for another 10 minutes and I'm still seeing a ton of crystals, honestly doesn't look to have improved much at all. This vial was previously heated and stored @100°F, yet crashed within a week.
EDIT: been at 202°F for at least 10 minutes now with no big change. Never seen a compound this resistant to going back into solution.
@Photon Would I be able to add ~5%, or 0.5ml, of BA after this is in solution again to help prevent future crashing? I figure BA is the way to go over BB only because it will be more impactful at much lower volumes, thus altering the concentration the least amount for the most benefit. Same question goes for TNE and other crash-happy compounds. I tolerate high BA concentrations just fine.
EDIT: been at 202°F for at least 10 minutes now with no big change. Never seen a compound this resistant to going back into solution.
@Photon Would I be able to add ~5%, or 0.5ml, of BA after this is in solution again to help prevent future crashing? I figure BA is the way to go over BB only because it will be more impactful at much lower volumes, thus altering the concentration the least amount for the most benefit. Same question goes for TNE and other crash-happy compounds. I tolerate high BA concentrations just fine.
Last edited:
Photon
Member
It will help but it'll probably still crash.
If you can't uncrash in 15m at 185f then the solvent content is probably too low.
Whistles77
Member
I spent a few hours trying to deal with a vial over the weekend. My only success was with wrapping in a wet paper towel and microwaving it directly.
It pained me to do, but there was enough crystals around the vial neck that I had to find some solution to trust it.
Jsilk757
Member
Had the same issue
The only thing that worked for me was the microwave trick
Wet a paper towel
Wrap one time around vial (1/4sheet)
Set microwave for two min
Stop every 20 sec and shake vial until no more crystals
Mine uncrashed at the 1 minute mark
AllGoodThings
Member
Would you add BA and BB and then retry, or just BA?
Sorry to bother you with so many questions, I greatly appreciate and respect your knowledge and experience.
Photon
Member
AllGoodThings
Member
@Jsilk757 @Whistles77
I actually haven't owned a microwave in over 8 years, so that isn't an option. Also, that's terrifying lol, gives me chills just thinking about doing that! Glad it worked for you both though!
I'm going to add some solvent and reheat with the mug warmer and see how it goes.
I actually haven't owned a microwave in over 8 years, so that isn't an option. Also, that's terrifying lol, gives me chills just thinking about doing that! Glad it worked for you both though!
I'm going to add some solvent and reheat with the mug warmer and see how it goes.
AllGoodThings
Member
I was afraid that would the more effective way to go, I was just hoping to not lower the concentration significantly, but it's useless as it is, so I guess I'll give it a shot.
@Arail what BA and BB concentration is the current Anadrol 50 batch brewed at? Just looking to know what I'm starting with here
RockyP
Member
From what I’ve researched Anadrol is particularly difficult to keep in solution without G or EO. Apparently its solubility window is very narrow and any changes in pressure or temp can cause it to crash. I’ve been able to uncrash mine using direct heat at 185 for 10-12 mins but I find that it crashes again even at 105F ambient temp (wipe warmer) within 4 hours. This has led me to conclude that this is why I kept getting delayed pip and redness / swelling 3 days post injection (it was crashing in tissue after injecting - seeing as how it re crashed at 105 and that’s more than my body temp). The vials I had that were not crashed pinned beautifully with no issues. But once it crashed it became unusable (for me) given these persistent issues of re crashing.
I just started my health phase so this is on the shelf for me indefinitely at this point, but I am eagerly following along to see if anyone can crack the code to make this product more sustainably usable.
I just started my health phase so this is on the shelf for me indefinitely at this point, but I am eagerly following along to see if anyone can crack the code to make this product more sustainably usable.
Last edited:
TallandSmall
Member
I think he was talking about albuterol if you heard that on his recent Q&A. In just ran out of the Helios and tempted to order more. The injectable yohimbine hits fast. Haven’t noticed much difference on the clen part.
BALLISTIC
Member
Yes same situation. Forming a very thick crystalization proving difficult to remedy.
My hot plate tops out at 176f. So I was able to evenly and cleanly wrap the vial in aluminum foil. My thought was more contact area heating the vial uniformly instead of conducting transfer through bottom of glass alone. This worked extremely well.
I'm not passing judgement on the microwave but that's really stupid whether it works or not. I'd also venture to say those who did have undoubtedly destroyed a large if not majority of the compound doing so. Microwaves cause dipole rotation in polar molecules. Safe to say, your no longer injecting at any guessable dosage. Microwaves don't heat uniformly, they target easier molecules first spiking temperatures which then transfer to the next.
Whistles77
Member
Dont think you're wrong. Hopefully the few second and the wet towel minimise that affect and the heat is mostly going into hearing the water rather than the oil, but other option had been to throw it out rather than risk injecting crashed stuff and the pip. I'll be trying your alu foil solution though.
RockyP
Member
Brother any idea how long the solution remained uncrashed (in terms of hours) following your use of this foil method? Best I've been able to get is 4 hours until it crashes again (and that's placing it in the wipe warmer at 105F after the direct heat of 185F gets it back into solution).
BALLISTIC
Member
Sorry I don't, once I use it, I place it back in a drawer and don't look at again until next use. Also my plate is timed, so I set it to 30min and walk away. Without the aluminum foil it occasionally took longer. I'm not complaining as I'd rather deal with this then have unnecessary chemicals. It just seems to crash hard and thick for me. Let the dick jokes roll. Haha
AllGoodThings
Member
After 183° for 15m, 196° for 10m, 202° for 10m, adding 1.5ml BB and 0.5ml BA, then another 25m at 196° and still seeing crystal stuck to the now nearly full vial, I gave up. I confirmed the temps on this relatively expensive mugwarmer are very accurate using a laser thermometer, so it's getting enough heat. I'll have to try BALLISTIC's aluminium foil method tomorrow
Last edited:
MoreShakesMoreCakes
New Member
Yes! Thank you!All taken care of.
BALLISTIC
Member
Damn, with that I don't know if even the foil will help. But let me know.
Similar threads
